SHURE MX393 C PDF

Boundary microphone provides high-quality sound for a wide range of applications due to its interchangeable condenser cartridge. It features programmable, silent membrane switches, LED indicators, and a low-profile design. There's never been smarter boundary microphones than the Microflex models from Shure. With many models to choose from, equipped with features like programmable, silent membrane switches, logic inputs and outputs, and LED indicators, Microflex Boundary microphones are the high-quality solution for a range of applications, such as altars, boardrooms and distance learning centers.

Author:Mar Kagazuru
Country:Kuwait
Language:English (Spanish)
Genre:Technology
Published (Last):3 February 2014
Pages:265
PDF File Size:11.70 Mb
ePub File Size:1.26 Mb
ISBN:484-7-74815-464-8
Downloads:58283
Price:Free* [*Free Regsitration Required]
Uploader:Meziktilar



Their high sensitivity and wide frequency range make them especially suitable for picking up speech and vocals in sound reinforcement and recording applications. Interchangeable cartridges provide the installer with greater flexibility and make it possible to easily reconfigure microphone coverage as the need arises. The MX and MX models include an internal preamplifier.

MX Series microphones take advantage of the principle that, at a barrier or boundary, the sound pressure level doubles. When placed near a sufficiently large boundary surface, the microphone has 6 dB higher sensitivity and approximately 3 dB greater direct-to-reverberant sound ratio.

Additionally they provide following benefits:. Microflex microphones use interchangeable cartridges that allow you to choose the polar pattern for different installations. Note: If using rear side-exit cable option, only drill two outer holes. For best low-frequency response and rejection of background noise, place the microphone on a large, flat surface, such as a floor, table, or lectern. To reduce reverberance, avoid reflective surfaces above or to the side of the microphone, such as beveled sides of pulpits or overhanging shelves.

Once placement has been determined, the microphones can be permanently installed. First, drill the hole in the selected area to allow the bottom entry cable to be conveniently routed out of sight. Then use the pressure sensitive adhesive to keep the microphone firmly in place. Note: The pressure sensitive adhesive will be extremely difficult to move once pressure has been applied. The DIP switches are covered with a piece of clear tape at the factory. Remove tape to modify the switch settings.

Be sure to set DIP switch 3 off factory default so that the mute button controls audio from the microphone. Use these settings if connecting the microphone to an automatic mixer or other device that mutes audio and controls the LED. Set DIP switch 1 for momentary or toggle. All measurements taken with microphone mounted on a wooden surface 76 x 76 cm. Positive sound pressure on diaphragm produces positive voltage on pin 2 relative to pin 3 of output XLR connector.

For contact information please visit www. The CE Declaration of Conformity can be obtained from: www.

Interchangeable Cartridges. Cartridge Polar Patterns. Cut slots into pads. Slide microphone forward to engage screws in slots. Microphone Placement For best low-frequency response and rejection of background noise, place the microphone on a large, flat surface, such as a floor, table, or lectern.

MXBE Once placement has been determined, the microphones can be permanently installed. Remove all debris from the mounting surface. Route the cable through the drilled hole. Connect the cable to a mixer or P. Pressure Sensitive Adhesive Thoroughly clean the application area with the included alcohol wipe. Removing the dust will allow the microphone to adhere well. Remove the adhesive backing and gently set the microphone into position. Once the microphone is in position, firmly apply pressure to the microphone.

Disconnect wires from screw terminals. Rotate boot and cable ccw to remove connector from threaded "L" bracket. Remove cable from microphone housing. Insert cable through access hole in microphone base. Insert cable connector through hole and thread it into "L" bracket. If desired, rubber strain relief can be reattached to cable end or removed from cable before fastening it to bracket. Re-connect wires to proper screw terminals on circuit board.

Insert supplied round rubber plug into unused side cable exit. Reinstall grille and foam screen. Insert cable through hole in mounting surface. Secure microphone to mounting surface. Connecting to an Automatic Mixer Use these settings if connecting the microphone to an automatic mixer or other device that mutes audio and controls the LED. Connect logic leads to the automatic mixer. Set DIP switch 3 on. This disbles the mute button the microphone passes audio regardless of whether the button is pressed or not.

Remove the resistor at R45 and reinstall it at location R Painting A supplied plastic paint shield B retainer C grille D foam screen E supplied adhesive masking strip F supplied rubber plug. Type Electret Condenser. Output Configuration Active Balanced. Signal-to-Noise Ratio Ref.

Polarity Positive sound pressure on diaphragm produces positive voltage on pin 2 relative to pin 3 of output XLR connector. Absolute maximum voltage: Power Requirements V DC , 2. Certifications Meets essential requirements of all applicable European Directives. Eligible for CE marking. Download PDF. Table of Contents.

ADAM SMITH TEORIA DEI SENTIMENTI MORALI PDF

Shure MX393/C

Boundary microphone provides high-quality sound for a wide range of applications due to its interchangeable condenser cartridge. It features programmable, silent membrane switches, LED indicators, and a low-profile design. There's never been smarter boundary microphones than the Microflex models from Shure. With many models to choose from, equipped with features like programmable, silent membrane switches, logic inputs and outputs, and LED indicators, Microflex Boundary microphones are the high-quality solution for a range of applications, such as altars, boardrooms and distance learning centers. Every Microflex Boundary microphone features one of the new interchangeable condenser cartridges.

KERO PALMISTRY PDF

General Description

Their high sensitivity and wide frequency range make them especially suitable for picking up speech and vocals in sound reinforcement and recording applications. Interchangeable cartridges provide the installer with greater flexibility and make it possible to easily reconfigure microphone coverage as the need arises. The MX and MX models include an internal preamplifier. MX Series microphones take advantage of the principle that, at a barrier or boundary, the sound pressure level doubles. When placed near a sufficiently large boundary surface, the microphone has 6 dB higher sensitivity and approximately 3 dB greater direct-to-reverberant sound ratio. Additionally they provide following benefits:. Microflex microphones use interchangeable cartridges that allow you to choose the polar pattern for different installations.

HENRI CHALLAN 380 PDF

Microflex Boundary

Thomann is the largest online and mail order retailer for musical instruments, light and sound equipment worldwide, having about 10m customers in countries and 80, products on offer. We are musicians ourselves and share your passion for making it. As a company, we have a single objective: making you, our customer, happy. We have a wide variety of pages giving information and enabling you to contact us before and after your purchase. Alternatively, please feel free to use our accounts on social media such as Facebook or Twitter to get in touch. Most members of our service staff are musicians themselves, which puts them in the perfect position to help you with everything from your choice of instruments to maintenance and repair issues.

Related Articles