LS3408 MANUAL PDF

Quick Links. Download this manual. Symbol LS Table of Contents. Page 4 Motorola. No right to copy a licensed program in whole or in part is granted, except as permitted under copyright law.

Author:Vushakar Samutaxe
Country:Panama
Language:English (Spanish)
Genre:Music
Published (Last):19 June 2009
Pages:41
PDF File Size:11.98 Mb
ePub File Size:7.87 Mb
ISBN:969-8-48347-888-6
Downloads:11240
Price:Free* [*Free Regsitration Required]
Uploader:Vulabar



Quick Links. Symbol LS Table of Contents. All rights reserved. No part of this publication may be reproduced or used in any form, or by any electrical or mechanical means, without permission in writing from Motorola.

This includes electronic or mechanical means, such as photocopying, recording, or information storage and retrieval systems. Page 8 Connecting a Keyboard Wedge Interface Page 9 Host Serial Response Time-out Page 10 Beep Style Page 11 Code 11 Check Digit Verification Page 12 Rules: Criteria Linked to Actions It includes basic setup and operation instructions.

Page Service Information Software type and version number Motorola responds to calls by e-mail, telephone or fax within the time limits set forth in service agreements.

If your problem cannot be solved by Motorola Enterprise Mobility Support, you may need to return your equipment for servicing and will be given specific directions. Page Chapter 1 Getting Started The scanner combines excellent scanning performance and advanced ergonomics to provide the best value in a lightweight laser scanner. Whether using it as a hand-held scanner or in presentation hands-free mode in a stand, the scanner ensures comfort and ease of use for extended periods of time.

Unpacking the Scanner Remove the scanner from its packing and inspect it for damage. If the scanner was damaged in transit, contact Motorola Enterprise Mobility Support at one of the telephone numbers listed on page xv. Page Setting Up The Scanner 1 - 3 Setting Up the Scanner Installing the Interface Cable Loosen the two screws on the cable clamp at the bottom of the scanner and gently pull the clamp away from the bottom of the scanner. Removing the Cable Clamp Page Connecting Power If Required 1 - 4 Symbol LS Product Reference Guide Close the clamp, push it back into place and tighten the screws on the clamp to secure the cable into the bottom of the scanner.

Closing the Cable Clamp Figure Connect the other end of the interface cable to the host see the specific host chapter for information on host connections. Connect the other end of the Synapse Smart Cable to the host. Removing the Interface Cable Loosen the two screws on the cable clamp at the bottom of the scanner and gently pull the clamp away from the bottom of the scanner.

Page Chapter 2 Scanning Chapter 2 Scanning Introduction This chapter provides beeper and LED definitions, techniques involved in scanning bar codes, general instructions and tips about scanning, and decode zone diagrams. Page Beeper Definitions Type. This is normal and usually happens when the PC cold boots. Page Led Definitions Ensure the scan line crosses every bar and space of the symbol. Laser light reflecting directly back into the scanner from the bar code is known as specular reflection.

This specular reflection can make decoding difficult. Page Scanning In Presentation Mode To scan a bar code, present the bar code and ensure the scan line crosses every bar and space of the symbol. Upon successful decode, the scanner beeps and the LED turns green. For more information on beeper and Page 31 Page Chapter 3 Maintenance And Technical Specifications This chapter provides suggested scanner maintenance, troubleshooting, technical specifications, and signal descriptions pinouts.

Maintenance Cleaning the scan window is the only maintenance required. A dirty window can affect scanning accuracy. Page Troubleshooting Ensure all cable connections are secure. Scanner is disabled. Otherwise, see the technical person in charge of scanning. Page 35 Interface cable is loose. Ensure all cable connections are secure. If 4 long low beeps are heard, a Ensure the scanner's communication transmission error was parameters match the host's setting.

Beeper Operation Page 39 Maintenance and Technical Specifications 3 - 7 The signal descriptions in Table apply to the connector on the scanner and are for reference only. For example, to set the beeper tone to high, scan the High Frequency beeper tone bar code under Beeper Tone on page User Preferences Default Parameters Table lists the defaults for user preferences parameters. To change any option, scan the appropriate bar To enable decoding of parameter bar codes, scan Enable Parameter Scanning.

When in reduced power mode, the scanner draws less current from its power source. Page Laser On Time Enter a leading zero for single digit numbers. For example, to set a Laser On Time of 0. In case of an error, or to Page Trigger Mode The laser scanning beam stays on until the laser-on timeout occurs or a decode occurs. If you pull the trigger again while in a decode session, the scanner beam returns to an aiming dot. Page Aim Duration Enter a leading zero for durations less than 1.

For example, to set an aim duration of 0. Page Chapter 5 Keyboard Wedge Interface The host computer accepts the keystrokes as if they originate from the keyboard. This mode of operation adds bar code reading functionality to a system designed for manual keyboard input. In this mode the keyboard keystrokes are simply passed through.

The connectors illustrated in Figure are examples only. The connectors may be different than those illustrated, but the steps to connect the scanner are the same. Turn off the host and unplug the keyboard connector. To change any option, scan the appropriate bar code s provided in the Keyboard Wedge Host Parameters section beginning on page If your keyboard type does not appear, see Alternate Numeric Keypad Emulation on page North American German Windows Page Ignore Unknown Characters Characters to send all bar code data except for unknown characters.

The scanner sounds no error beeps. The scanner sounds an error beep. This sets the Keystroke Delay parameter to a minimum of 5 msec as well. Enable Intra-Keystroke Delay Page Function Key Mapping Table on page Enable this parameter to send the keys in bold in place of the standard key mapping. Table entries that do not have a bold entry remain the same whether or not you enable this parameter. Page 60 5 - 12 Symbol LS Product Reference Guide Otherwise, the unbolded keystroke is sent.

Page 65 The keystroke in bold is sent only if you enable Function Key Mapping on page Use the RS interfaced to attach the scanner to point-of-sale devices, host computers, or other devices with an available RS port i.

Page Connecting An Rs Interface Connect the other end of the RS interface cable to the serial port on the host.

Connect the power supply to the serial connector end of the RS interface cable. Plug the power supply to an appropriate outlet. Ensure that all connections are secure. To change any option, scan the appropriate bar code s provided in the Parameter Descriptions section beginning on page When CTS is high, scanning is enabled.

Page 75 ID characters listed in Table below. Do not enable the Transmit Code ID feature for these terminals. Set the scanner's baud rate to match the baud rate setting of the host, or data may not reach the host device or may reach it in distorted form. Select the parity type according to host device requirements. Select Odd parity to set the parity bit value to 0 or 1, based on data, to ensure that the coded character contains an odd number of 1 bits.

None Check Receive Errors Select whether or not to check the parity, framing, and overrun of received characters. The parity value of received characters is verified against the parity parameter selected above.

Check For Received Errors Enable Page Stop Bit Select The stop bit s at the end of each transmitted character marks the end of transmission of one character and prepares the receiving device for the next character in the serial data stream.

Select the number of stop bits one or two to match the number the receiving terminal is programmed to accommodate. If, after Host Serial Response Time-out default , the CTS line is still asserted, the scanner sounds a transmit error and discards any scanned data. If CTS is not asserted during this time, the scanner issues an error indication and discards the data.

After three unsuccessful attempts to send data after receiving NAKs, the scanner issues an error indication and discards the data. If it does not receive the XON within this time, the scanner issues an error indication and discards the data.

AYOOB FILES THE BOOK PDF

Motorola Symbol LS3408 Product Reference Manual

.

RAJAKESARI NOVEL PDF

Zebra LS3408-FZAR0200AR User Manual

.

LIBRO ARREBATOS CARNALES 2 PDF

LS3408 Handheld Scanner Support

.

Related Articles