This site also contains information about the preconfigured Wi-Fi settings of the device. In the bottom part of this website, you will find a manual for accessing the user interface of this router and resetting its factory settings. Accessing the user interface is necessary when you want to change the router configuration. For the Belkin F5D, you have to do the following steps for access:. Resetting default settings is especially helpful when you have changed and forgotten the login data for the user interface.

Author:Zulkirn Votaxe
Language:English (Spanish)
Published (Last):22 December 2008
PDF File Size:6.88 Mb
ePub File Size:20.6 Mb
Price:Free* [*Free Regsitration Required]

Quick Links. Download this manual. Table of Contents. Page 3: Table Of Contents Introduction If difficulties persist even at close range, please contact Belkin Technical Support. Page 9 Introduction For more information regarding our networking products, visit our website at www. Page Product Overview In minutes you will be able to share your Internet connection and network your computers.

The switch features automatic detection so it will adjust to the speed of connected devices. Actual throughput is typically lower than the connected data rate and will vary depending on your networking environment. Page 14 Knowing your Router The Router has been designed to be placed on a desktop. All of the cables exit from the rear of the Router for better organization and utility. It blinks rapidly when information is being sent over the port between the Router and the modem.

Use the restore option in instances where you may have forgotten your custom password. You can use it to get your Router up and running in minutes. Place the Router next to the modem with the antennas raised. Locate the networking cable that connects your modem and computer. Turn off any firewall or Internet-connection-sharing software on your computer. Insert the CD into your computer. Page 21 Connecting and Configuring your Router Confirmation Screen Verify that you have completed all setup steps by checking the box to the right of the arrow.

Page 22 Connecting and Configuring your Router Progress Screen Setup Assistant will show you a progress screen each time a step in the setup has been completed. This is the name of your wireless network to which your computers or devices with wireless network adapters will connect.

Page 24 Connecting and Configuring your Router Requesting Internet Account Info if needed If your Internet account requires a login and password, you will be prompted with a screen similar to the illustration below. Select your country or ISP from the drop-down boxes. Wait for the on-screen instructions. Note: Do not disconnect any cable or power off the Router while the Router is rebooting. Page 26 Connecting and Configuring your Router 2. The Setup Assistant will now check your connection to the Internet.

You can begin surfing by opening your browser and going to any website. Page 29 Connecting and Configuring your Router Troubleshooting If the Setup Assistant is not able to connect to the Internet, you will see the following screen. Follow the on-screen instructions to go through the troubleshooting steps. Page 30 Connecting and Configuring your Router Optional: Assistance Connecting Other Computers This optional step will help you to connect additional wired and wireless computers to your network.

Follow the on-screen instructions. At this point, your Router is set up and working properly. It is now time to At this point, your Router is set up and working properly. Page 31 Connecting and Configuring your Router Connecting computers with wired cables Computers with wired network adapters can use this network.

If you still need to install those adapters, do this now. Page 32 Connecting and Configuring your Router Congratulations Once you have verified that your other wired and wireless computers are properly connected, your network is set up and working.

You can now surf the Internet. Locate the network cable that is connected between your modem and your computer and unplug it from your computer, leaving the other end connected to your modem.

If it is not, recheck your connections. The home page is visible to any user who wants to see it. All advanced setup pages can be reached from this page. Logging into the Router will take you to a separate login page where you will need to enter a password.

Some dynamic connection types may require a host name. If you are not sure if your ISP requires a service name, leave this blank. Type in the information provided by your ISP in the space provided. Disconnect after X Enter this information below. Choosing your state from the drop-down menu 6 will automatically fill in your login server IP address. Page 48 Internet service. Belkin has provided the ability to clone copy the MAC address of the computer into the Router. Page Changing Lan Settings There is no need to change the subnet mask.

This is a unique, advanced feature of your Belkin Router. It is possible to change the subnet mask if necessary; however, do NOT make changes to the subnet mask unless you have a specific Page 51 IP address to change. You can set a local domain name network name for your network. There is no need to change this setting unless you have a specific advanced need to do so. You can name the network From this tab you can make changes to the wireless network name SSID , operating channel, encryption security settings, and configure the Router to be used as an access point.

You can change this to anything you choose, or you can leave it unchanged. There are three modes. In the United States, there are 11 channels. In the United Kingdom and most of Europe, there are 13 channels. If you are in an environment where there is no other or very little Enable WPS through the screen illustrated below. The client will be automatically enrolled into your wireless network within two minutes. Most of the Belkin wireless cards have driver updates available for download from the Belkin support site: www.

This setting will have to be identical on the wireless clients that you set up. Enter your pre-shared key PSK. This can be from eight to 63 characters and can be letters, numbers, or symbols. At the time this User Manual was published, a security patch from Microsoft is available for free download. This patch works only with Windows XP. The Router can be configured to work as a wireless network access point.

In AP mode, the Router will need to be configured with an IP address that is in the same subnet as the rest of the network that you will bridge to.

Note: This list applies only to wireless computers. This list can be configured so any computer attempting to access the wireless network that is not specified in the filter list will be denied access.

Any computer in the list will not be allowed access to the wireless network. Restriction can be set for a single computer, a range of computers, or multiple computers. To restrict Internet access to a single computer for example, enter the IP address of the computer you wish to restrict access to in the IP fields 1. This may be necessary if the firewall is causing problems with an application such as a game or video conferencing application.

Once you have your registration, follow the directions below. Enter your DynDNS. By pinging a specific IP address and receiving a response from the IP address, a hacker can determine that something of interest might be there. Restarting the Router Sometimes it may be necessary to restart or reboot the Router if it begins working improperly.

The following message will appear. Restarting the Router can take up to 60 seconds. It is important not to turn off the power to the Router during the restart. When the countdown A second countdown will appear on the screen. When the countdown reaches zero, the Router will be restarted.

The Router home page should appear automatically. It is recommended that you back up your settings before you restore all of the defaults. A window will open that allows you to select the location where you A window will open that allows you to select the location where you want to save the configuration file.

The configuration is now saved. A window will open that allows you to select the location of the configuration file. A reminder window will appear. It will take up to 60 seconds for the A reminder window will appear. It will take up to 60 seconds for the configuration restoration to complete.

Firmware updates contain feature improvements and fixes to problems that may have existed. A window will open that allows you to select the location where you want to A window will open that allows you to select the location where you want to save the firmware file.


Belkin F5D9230-4 User Manual



Belkin Wireless G Plus MIMO Router F5D9230-4 User Manual



Manually setting up the Belkin Wireless G+ MIMO Router, F5D9230-4


Related Articles